ASTM B187 PDF

Specs ASTM B Alloy OFE OFHC Copper Round Rod. View More · Alloy Copper Rectangle Square Edge. ASTM B – Free download as PDF File .pdf), Text File .txt) or read online for free. C Round OFE SH Copper Products Rod. H04 (hard). 12 Foot Mill Lengths. ASTM B, ASTM F Diameter. (Inches). Diameter. Tolerance. Pounds.

Author: Mojin Zutilar
Country: Gabon
Language: English (Spanish)
Genre: Photos
Published (Last): 12 October 2010
Pages: 259
PDF File Size: 4.83 Mb
ePub File Size: 9.8 Mb
ISBN: 456-3-14930-846-7
Downloads: 71406
Price: Free* [*Free Regsitration Required]
Uploader: Mulkree

Historical Version s – view previous versions of standard. Sawed deburred bar to use Table 5 and Table 7. E C, C, and C are oxygen-free coppers with the addition of a speci?

This standard has been approved for use by agencies of the Department of Defense. A B Width times thickness, disregarding any rounded corner or edges. E See Appendix X1. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. C NOTE 1—The arc shall not necessarily be tangent at points, A, but shall be substantially symmetrical with the axis of the product, and the product shall be commercially free from sharp, rough, or projecting edges.

A number in parentheses indicates the year of last reapproval. Short lengths may be included as prescribed in Table 9. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. The compositions of these alloys are equivalent to C plus the intentional addition of silver.

  EL PRINCIPE QUE TODO LO APRENDIO EN LOS LIBROS PDF

Last previous edition approved in as B — Combining values from the two systems may result in nonconformance with the specification. Shapes shall not include tube and pipe or other hollow sections. Over 1 [25] to 35 [] 2 [50] incl.

ASTM B187 Grade C10200 H04 bar

Products shall be produced in tempers O60 soft annealedand H04 hard. Originally approved in Rolled or drawn edges to use Table 4 and Table 6. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Measure the maximum depth of arc to the nearest 1?

Over 2 [50] to 33 [] 3 [75] incl. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. ASTM International takes no position respecting the validity of any patent rights asserted in connection sstm any item mentioned in this standard.

Products shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional mass, diameter, thickness, width, shape, specified and stock lengths, straightness, edge contour, and radius of edges or cornersmechanical tensile, yield and h187 strengths, elongation, Rockwell hardness, and embrittlementelectrical resistivity, and chemical composition requirements.

Current edition approved Apr. Over 4 [] to 12 [] incl. Over 3 [75] 30 [] Bar: This term means that a wire 1 m in astj and weighing 1 g would have wstm resistance b18 0. The surface is similar in texture to that of the outside surface of an orange. D In any case, a minimum gage length of 1 in. Round, Hexagonal, Octagonal—See Table 3. A Tolerances, Plus and Minus,A in. F Special agreement shall be made between the manufacturer or supplier and the purchaser.

  CATTLEYA FILETYPE PDF

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. C, refer to the Annex of Speci? Mechanical Property Requirements This is equivalent to a resistivity value of Committee B05 has identi? Impurity maximums in ppm of C shall be: Over 4 to 9 [ to ] incl. Link to Active This link will always route atsm the current Active version of the standard.

The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. The corners, A, will usually be sharp, but shall not have rough or projecting edges.

ASTM B – 00 Standard Specification for Copper Bar, Bus Bar, Rod, and Shapes

The copper value is exclusive of Ag. NOTE 2—For the purpose of determining conformance with the dimensional requirements prescribed in this speci? Materials and Manufacture 6.

G Oxygen and trace elements may vary depending on the process. Over 1 to 11? Except as otherwise speci? Within the text, the SI units are shown in asfm.